Approx. Rs 18,000 / PieceGet Latest PriceProduct Details:
|Range||0 - 1000microm (0 - 40mils)|
|Scale||2microm (0.1 mil)|
|Dimensions||105 x 55 x 25mm (4.1 x 2.2 x 1inch)|
|Version||Metric & Imperial Version|
Elcometer 123 Surface Profile Gauge is easy to use gauge measures the peak-to-valley height of a blast cleaned surface.
The average of a series of measurements provides an indication of the surface roughness and allows the surfaces to be compared as blasting proceeds. This is Metric and Imperial version. Elcometer is a trademark of Elcometer Ltd., UK, registered in the UK and other countries.
|E123A--M-||Elcometer 123 Surface Profile Gauge, Metric Version|
|E123A--E-||Elcometer 123 Surface Profile Gauge, Imperial Version|
|Certificate Available||Certificate of Calibration: issued for Fixed Calibration equipment and shows readings and traceability.|
Accredited Certificate: can be issued for Fixed Calibration Equipment and a full UKAS traceable certificate is issued from an independent Calibration Laboratory.
|Packing List||Elcometer 123 Surface Profile Gauge, glass slide, 2mm Allen key, carry case and operating instrument|
Approx. Rs 2,600 / RollGet Latest PriceProduct Details:
|Minimum Order Quantity||1 Roll|
|Usage||Surface Profile Checking|
Approx. Rs 4 Lakh / PieceGet Latest PriceProduct Details:
SCM Meter Salt Contamination Elcometer
Being an industry leader, we offer a unique range of Scm meter salt contamination elcometer, which is 130 SCM400 salt contamination meter. The soluble salts are wrapped up in a special filter paper soaked with distilled water. Our range of product helps in measuring the conductivity of wet paper, measure the level of the salt and display the result on ugcm-2. Following are the various specification of our product.
Approx. Rs 8,900 / PieceGet Latest PriceProduct Details:
|Model||Shot Blasting Comparator|
Approx. Rs 4,000 / PieceGet Latest PriceProduct Details:
Our expert team assists us in offering a diverse range of surface comparator elcometer that is elcometer 125 surface comparator. It permits the estimation of surface roughness by both sight and touch. These are available in both shot and grit metric units only. In order to use it effective and proper preparation of surface even before coating is important. Make sure that the accurate profile or roughness has been generated. In case if the profile is too low it will reduce the coating to the surface on the other hand if the profile is too high then there will be danger that even leads to uncoated profile peak allowing rust spots to occur.Available in both grit and shot
Approx. Rs 3,500 / PieceGet Latest PriceProduct Details:
We are a known for offering a qualitative range of surface profile gauge elcometer that is elcometer 223 digital surface profile gauge. This is operated with a battery easily and is used to measure the peak-to-valley height of a surface almost like Elcometer123 analogue equivalent apart from one difference such as added benefit of direct RS232 output.
Approx. Rs 2,650 / PieceGet Latest PriceProduct Details:
|Minimum Order Quantity||1 Piece|
Testex Press-O-Film Replica Tape
Press-O-Film (POF) consists of a layer of crushable plastic microfoam coated onto a polyester film of highly uniform thickness.
When compressed against a roughened material, Press-O-Film accurately replicates details of its surface roughness.
The impression can be studied in several ways:
Testex Tape is popularly called as Press-O-Film. Press-O-Film provides surface profile of a basted cleaned surface. It can produce virtually exact replicas of the blasted surface profile, which can be measured, using a snap gauge. Testex offers a simple and very accurate method of measuring blasted profiles. Press-O-Film consists of layer of crushable plastic micro foam coated onto a polyester film of highly uniform thickness. Using surface profile gauge or testex tape can test surface roughness. Most commonly used testex tape as it can give permanent record of the surfaces. Place the Testex Tape (Press-O-Film) firmly on the blasted surface, apply moderate pressure with the burnishing tool, the replica has now been taken and can be measured using the snap gauge. Testing & Inspection can be done in three easy steps. Detailed procedure is furnished with testex kit or tapes. Testex Tape is supplied in a roll containing 50 tests and is available in four different grades to cater for different applications. The snap gauge is supplied in a carrying case with a burnishing tool. Paint applicators, inspectors and researchers for its simple operations and results prefers to use Testex tapes (Press-O-Film) Testex Tape (Press-o-film) complies with ASTM, NACE and SSPC methods measurement. ASTM- Reproducibility is given in ASTM Standard 4417-93 for both "X-coarse" and "coarse" grade replica tape. NACE- Standard RP0287-95 addresses the issue of accuracy of measurement, test results. SSPC- The Society for Protective Coatings, recommends a minimum of three measurements of profile per 100 square feet (10 square meters). ISO- International Organization for Standards- Draft Standard ISO8503-5 describes preparation of steel substrates before application of paint and related products. Testex kit comprises two rolls Press-O-Film (X Coarse supplied as standard, specify different grade if required), snap gauge and burnishing tool.
Approx. Rs 1,950 / PieceGet Latest PriceProduct Details:
Our company offers a wide range of WFT combs elcometer that is 112 & 3236 hexagonal wet film combs is made from high quality stainless steel to ensure its long service life, durability and reusable. These are highly suitable for measuring thickness of coatings up to 3000µm (120mils) range.
How to use a wet film comb
Furthermore, in order to use this wet film comb you first need to place a comb perpendicular that to touching the substrate. Wait for few seconds while holding the comb in position until the teeth are wet. Now take away the comb from the film. Finally the thickness of the wet film lies between the biggest wet tooth and value coated and dry tooth value or the smallest value uncoated.
Approx. Rs 1,950 / PieceGet Latest PriceProduct Details:
These hexagonal precision formed stainless steel wet film combs are long lasting and reusable and are supplied in a range of thicknesses measuring up to 3000µm (120mils).
These six sided combs vary in size, giving either 24 or 36 measurement steps, depending on the comb, providing increased accuracy.
Using a wet film comb
Place a comb perpendicular to and touching the substrate. Hold the comb in position and wait a few seconds until the teeth are wet. Remove the comb from the film. The wet film thickness lies between the biggest value ‘coated’ or ‘wet’ tooth and the smallest value ‘uncoated’ or ‘dry’ tooth.
|K0003236M201||20 - 370µm||20, 30, 40, 50, 60, 70, 80, 90, 100, 110, 120, 130, 150, 170, 190, 210, 230, 250, 270, 290, 310, 330, 350, 370µm|
|K0003236M202||25 - 2000µm||25, 50, 75, 100, 125, 150, 175, 200, 225, 250, 275, 300, 350, 400, 450, 500, 550, 600, 650, 700, 750, 800, 850, 900, 950, 1000, 1100, 1200, 1300, 1400, 1500, 1600, 1700, 1800, 1900, 2000µm|
|B112----1B||25 - 3000µm||25, 50, 75, 100, 125, 150, 175, 200, 225, 250, 275, 300, 350, 400, 450, 500, 550, 600, 650, 700, 750, 800, 850, 900, 1000, 1100, 1200, 1400, 1600, 1800, 2000, 2200, 2400, 2600, 2800, 3000µm|
|K0US3236M203||0.5 - 15mils||0.5, 0.75, 1.0, 1.25, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 8, 9, 10, 11, 12, 13, 14, 15mils|
|K0US3236M204||1 - 80mils||1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, 32, 34, 36, 38, 40, 42, 44, 46, 48, 50, 55, 60, 65, 70, 75, 80mils|
|B112----2B||1 - 120mils||1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, 32, 34, 36, 38, 40, 45, 50, 55, 60, 70, 80, 90, 100, 110, 120mils|
|Dimensions and Weight|
|53 x 50 x 1mm (2.09 x 1.97 x 0.04”), 10g (0.35oz)|
|Elcometer 3236M202/M204||77 x 90 x 1mm (2.95 x 3.54 x 0.04”), 22g (0.77oz)|
|Elcometer 112||75 x 65 x 1mm (2.95 x 2.54 x 0.04”), 20g (0.7oz)|
Explore More Products